Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Calculate the maximum deflection with consideration of initial slippage.
Este ejemplo de verificación se basa en el ejemplo de verificación 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Un sistema de una sola masa con juego y dos muelles se deforma inicialmente. Determine the natural oscillations of the system - deflection, velocity, and acceleration time course.
Una viga de acero con una sección cuadrada está cargada con un esfuerzo axil y una carga distribuida. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Una viga larga y delgada lleva una masa concentrada y está cargada por una fuerza dependiente del tiempo. It is simply supported. The problem is described using the following parameters. Determine the deflections in the given test times.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
Considere una viga W 18 x 50 según ASTM A992 para el vano y cargas vivas y muertas uniformes como se muestra en la figura 1. La barra está limitada a un canto nominal máximo de 18 pulgadas. La flecha de la carga viva está limitada a L/360. La viga está apoyada y arriostrada continuamente. Verifique la resistencia a flexión disponible de la viga seleccionada, según LRFD y ASD.
Un voladizo está completamente fijo en el extremo izquierdo y cargado por una fuerza transversal y una fuerza axil en el extremo derecho. The tensile strength is zero and the behavior in the compression remains elastic.
Un voladizo de sección rectangular tiene una masa al final. Furthermore, it is loaded by an axial force. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
Demuestre que el acoplamiento de diferentes elementos dimensionales no afecta a los resultados. A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.
Consider an ASTM A992 W 18×50 beam forspan and uniform dead and live loads as shown in Figure 1. La barra está limitada a un canto nominal máximo de 18 pulgadas. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
Determine las flechas máximas del bloque considerando o omitiendo el efecto cortante. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
Un cable o membrana de acero con pasadores en ambos extremos se carga mediante una carga distribuida. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. Se omite el peso propio. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Un sistema monomasa con amortiguador está sometido a una fuerza de carga constante. Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.
Una consola hecha de un redondo está cargada por una carga uniforme excéntrica. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
El objetivo de este ejemplo es demostrar un proceso irreversible causado por la fricción. After the loading and unloading, the end-point is in a different position than where it was at the beginning. Determine the movement of the node in the X direction.
Un voladizo con una sección circular está cargado por una fuerza de flexión concentrada y un momento de torsión. The aim of this verification example is to compare the reduced stress according to the von Mises and Tresca theories.
Una estructura hecha de un perfil en I está incrustada en los apoyos de la horquilla. The axial rotation is restricted on both ends while warping is enabled. The structure is loaded by two transverse forces in the middle. The verification example is based on the example introduced by Gensichen and Lumpe.
Un cable está cargado por medio de una carga uniforme. This causes the deformed shape in the form of the circular segment. Determine the equilibrium force of the cable to obtain the given sag of the cable. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Una placa ortótropa cuadrada en capas está completamente fijada en su punto medio y sometida a presión. Compare the deflections of the plate corners to check the correctness of the transformation.
Un voladizo está completamente fijado en el extremo izquierdo y cargado por un momento flector en el extremo derecho. El material tiene diferentes resistencias plásticas a tracción y compresión.
Se selecciona una barra en forma de W de ASTM A992 para soportar una carga muerta de 30.000 kips y una carga viva de 90.000 kips en tracción. Verify the member strength using both LRFD and ASD.
Una barra ligeramente inclinada está cargada por una fuerza concentrada, sostenida por un muelle en un extremo y apoyada en el otro extremo. Assuming large deformations and neglecting the member's self-weight, determine its maximum upward deflection.
Determine la resistencia a compresión axial admisible de una viga articulada de 2,5 m de largo de varias secciones hechas de aleación 6061-T6 y coaccionada lateralmente para evitar el pandeo sobre su eje débil de acuerdo con el Manual de diseño de aluminio 2020.
Una placa delgada está completamente fija en el extremo izquierdo y cargada con una presión uniforme. El material plástico se considera para el cálculo.
A structure is made of two trusses of unequal length, which are embedded into the hinge supports. The structure is loaded by concentrated force. Se omite el peso propio. Determine the relationship between the loading force and the deflection, considering large deformations.